20.109(S24):M2D6

Introduction

In this laboratory session, you will assess how effective your bioremediation system is at removing cadmium from the cell media.

In the last laboratory session, you prepared samples for analysis using inductively coupled plasma optical emission spectroscopy (ICP-OES). This technique is also known as ICP-AES, with the "A" representing "atomic". With this approach, a solution containing unknown elements is dissolved in acid to create a solution of soluble elements. These elements are pumped through a nebulizer to create a consistent fine spray. Inside the chamber, a quartz torch contained in an argon-cooled induction coil is lit, leading to the generation of a stable plasma "flame" capable of reaching 10,000K (the reported temperature on the surface of the sun).

As elements are aerosolized through the nebulizer, they are sprayed into the plasma where they are ionized with the electrons taking up the thermic energy emitted by the plasma and thus reaching an excited state. As the electrons fall back to ground level, they emit light at specific optical wavelengths that can be detected by the spectrometer. This approach allows us to determine the presence of elements in a sample by taking advantage of characteristic emission patterns of different elements. This data can then be processed to determine the elemental composition of samples, as well as differences in elemental concentrations between samples.

Protocols

Part 1: Review collection of ICP-OES data

ICP-OES equipment

Due to the training required to operate the machinery, the teaching staff and Dr. Jifa Qi have generated the ICP-OES data you will analyze. Please review the following steps to help conceptualize how the data were generated.

1. Enter the ICP-OES facility and place samples in fume hood while setting up the equipment.
2. Open the liquid argon regulator valve to begin the flow of argon gas to the ICP apparatus.
3. Turn on the chiller to cool the ICP apparatus during operation.
4. Tighten tubing connecting autosampler to nebulizer.

Ion nebulizer

Plasma torch behind protective layers

1. Open the ICP Expert program and temporarily boost the argon gas flow to purge the system and maintain steady gas flow.
2. Use the instrumentation panel in ICP Expert to light the plasma torch.
   • Plasma must be burn for 20 minutes before data can be collected.
3. Ensure collection probe is place in rinse solution.
4. Place samples in autosampler.
5. Before beginning experimental run, verify the following conditions to ensure machine is operational.
   • Periodic bubbles present in drain lines for spray chamber and autosampler.
   • Stable fog present in nebulizer sample chamber.
   • Stable torch flame.
6. Set the number of standards and samples on the autosampler map to set order of sample processing.
7. Set parameters of sampling as listed below:
   • 3 replicates per sample
   • RF power = 1.2 kW
   • pump speed = 12rpm
   • read time = 5s
   • rinse time = 30s
   • stabilization time = 15s
   • nebulizer flow = 0.70 L/min
   • plasma flow = 12 L/min
   • radial viewing mode
   • viewing height = 8mm
8. Set element and wavelength to be tested
   • If unsure of which wavelength is ideal for elements under analysis, select all available wavelengths
9. Save program file.
10. Begin ICP-OES testing program.

Part 2: Analyze ICP-OES data

ICP-OES uses replicate measurements of each sample to identify signal intensity at wavelengths previously determined to be indicative of a particular metal. It is possible to examine all available wavelengths to identify any unknown metals in a sample, or to select particular wavelengths to focus on identifying particular metals of interest. Additionally, ICP-OES allows users to calibrate measurements against known metal standards to allow for a concentration measurement (in parts per million) of each identified metal in the sample.

Once a run is complete, multiple documents of data are generated to allow for detailed examination of the data. These data files have been uploaded to the Class Data tab of the wiki to allow for further analysis.

1. Open the file called "Sp24_ICP-OES_Detailed with Calibrations". This file contains details on the experimental parameters used to collect data, the calibration curves for each standard at each wavelength tested, and all the raw data for both standards and samples.
   • One key piece of data in this file is the linear relationship between the known concentrations of cadmium in the standard curve at each wavelength. The data is plotted with an R-squared value, and the calculated concentration of each standard is calculated at each wavelength.

1. Using this standard curve calibration data, consider the following questions and note them in your laboratory notebook.

In your laboratory notebook, complete the following:

• Are there any particular wavelengths that appear entirely accurate for measuring cadmium (looking at calculated ppm and fit of the standard curve)?
• Would you exclude any wavelengths from cadmium measurement based on their calibration?

ICP-OES is a well studied technique, and its analysis is continually being refined as new information is established. This also means that resources on best practices, and potential problems exist to guide scientists to obtain accurate results. One of these resources is linked here. This is an interactive periodic table meant to consolidate not only elemental information, but also information about potential sources of interference when using spectroscopy to identify the elemental composition of a sample.

1. Click on cadmium in the periodic table and scroll down to "Atomic Spectroscopic Information" located at the bottom of the right-hand panel.
   • The elements listed here can be sources of interference (and therefore inaccurate measurements) at the wavelengths listed.

Consider the following questions and note them in your laboratory notebook.

In your laboratory notebook, complete the following:

• Do you expect to see any potential interference from other elements in your sample? If so, which wavelengths are the most likely to be affected by interference?

Now that you had identified any problematic wavelengths that you want to exclude from your analysis, you can take a closer look at the data for each of the samples in the class.

1. From the class data page, download the csv file. This file contains the data for all samples in a format more amenable to analysis. The first sheet of this file contains the data, and the second sheet contains a key to indicate the identity of each sample.
2. There is a baseline control sample of untransformed ΔMet17 yeast for each section.
3. Identify the ppm for cadmium for each control sample at the wavelength(s) of your choosing. Record these values in your notebook.
4. Identify the ppm for your group's sample for cadmium at the same wavelength(s)
   • What does a lower ppm indicate? (Hint: think about the experimental set up)
5. Record these values in your notebook.

In your laboratory notebook, complete the following:

• Record your ppm measurements from ICP-OES.

Reagents list

• Complete synthetic media - tryptophan + Cysteine, Methionine, and galactose (CSM-G) media: 0.17% yeast nitrogen base without amino acid and ammonium sulfate (BD Bacto), 0.5% ammonium sulfate (Sigma), 0.13 % amino acid mix lacking tryptophan (US Biologicals), 0.005% Methionine (Sigma), 0.005% Cysteine (Sigma), 2% galactose (Sigma), 0.1% adenine hemisulfate (Sigma)
• Cadmium nitrate (Sigma), stock concentration= 100mM
• TraceCERT cadmium standard for ICP (Sigma)

Navigation links

Next day: Visualize cadmium sequestration and assess quality of cadmium sulfide production

Previous day: Perform flow cytometry and harvest cells to test cadmium sequestration