Difference between revisions of "20.109(F16):Complete immuno-fluorescence assay (Day6)"

Introduction

As a reminder, since the previous laboratory session your experimental cells were treated with gamma-irradiation and both the experimental and controls cells were fixed with paraformaldehyde. Today you will permeabilize the cells you seeded. The permeabilization step is critical as it allows the antibodies that bind XXY to pass through the cell membrane.

The ability to bind specific proteins using antibodies, or immunoglobulins, is critical in Western blot analysis. Antibodies are typically 'raised' in mammalian hosts. Most commonly mice, rabbits, and goats are used, but antibodies can also be raised in sheep, chickens, rats, and even humans. The protein used to raise an antibody is called the antigen and the portion of the antigen that is recognized by an antibody is called the epitope. Some antibodies are monoclonal, or more appropriately “monospecific,” and recognize one epitope, while other antibodies, called polyclonal antibodies, are in fact antibody pools that recognize multiple epitopes. Antibodies can be raised not only to detect specific amino acid sequences, but also post-translational modifications and/or secondary structure. Therefore, antibodies can be used to distinguish between modified (for example, phosphorylated or glycoslyated proteins) and unmodified protein.

Monoclonal antibodies overcome many limitations of polyclonal pools in that they are specific to a particular epitope and can be produced in unlimited quantities. However, more time is required to establish these antibody-producing cells, called hybridomas, and it is a more expensive endeavor. In this process, normal antibody-producing B cells are fused with immortalized B cells, derived from myelomas, by chemical treatment with a limited efficiency. To select only heterogeneously fused cells, the cultures are maintained in medium in which myeloma cells alone cannot survive (often HAT medium). Normal B cells will naturally die over time with no intervention, so ultimately only the fused cells, called hybridomas, remain. A fused cell with two nuclei can be resolved into a stable cell line after mitosis.

Generating monoclonal antibodies.

To raise polyclonal antibodies, the antigen of interest is first purified and then injected into an animal. To elicit and enhance the animal’s immunogenic response, the antigen is often injected multiple times over several weeks in the presence of an immune-boosting compound called adjuvant. After some time, usually 4 to 8 weeks, samples of the animal’s blood are collected and the cellular fraction is removed by centrifugation. What is left, called the serum, can then be tested in the lab for the presence of specific antibodies. Even the very best antisera have no more than 10% of their antibodies directed against a particular antigen. The quality of any antiserum is judged by the purity (that it has few other antibodies), the specificity (that it recognizes the antigen and not other spurious proteins) and the concentration (sometimes called titer). Animals with strong responses to an antigen can be boosted with the antigen and then bled many times, so large volumes of antisera can be produced. However animals have limited life-spans and even the largest volumes of antiserum will eventually run out, requiring a new animal. The purity, specificity and titer of the new antiserum will likely differ from those of the first batch. High titer antisera against bacterial and viral proteins can be particularly precious since these antibodies are difficult to raise; most animals have seen these immunogens before and therefore don’t mount a major immune response when immunized. Antibodies against toxic proteins are also challenging to produce if they make the animals sick.

Generating polyclonal antibodies.

For immuno-fluorescence, ...

Protocols

Part 1: Communication Lab workshop

Part 2: Complete H2AX assay

At this point in the assay sterility is no longer a concern and you will complete the following steps in the main laboratory at your bench.

1. Obtain your two 12-well plates from the 4°C cooler.
2. Gather aliquots of Triton X-100 and TBS from the front laboratory bench.
   • Prepare a 0.2% Triton X-100 solution (v/v) using the TBS.
3. Aspirate the 1x PBS from the wells in your 12-well plates.
4. Permeabilize the cells by adding 500 μL of the Triton X-100 solution and incubate for 10 min at room temperature.
5. Obtain an aliquot of blocking solution from the front laboratory bench.
6. Aspirate the Triton X-100 solution and add 500 μL of blocking solution, then incubate for 60 min at room temperature.
7. With 5 min remaining of the blocking solution incubation, prepare the primary antibody.
   • Dilute the anti-H2AX antibody 1:100 in an aliquot fresh blocking solution.
8. Aspirate the blocking solution.
9. Add 350 μL of the diluted primary antibody solution.
10. Carefully move your plates to the 4 °C cooler.

Your samples will incubate at 4 °C in the primary antibody solution until your next laboratory session. The teaching faculty will replace the primary antibody solution with the diluted secondary antibody solution, Alexa Fluor 488 Goat Anti-Mouse diluted 1:200 in blocking solution. Following the Business Proposal Presentations, you will visualize the results of your H2AX assay.

Reagents

Navigation links

Next day: